In 2-3 months will get new sway bars.

[FiveLeeter918]

Can you elaborate ?? I was on my back and jack stands too !!!!!!! Do you have a video ? Just curious !! I tried every possible way and I couldn't snake the MOTHER FLOWER out !!

Are you referring to the insulator mounts? I just snaked it out through the driver side. No video unfortunately

 

[joe raptor]

they're already installed , my mechanic had to drop the exhaust system and replace the sway bar with no problems, to bad I don't have a lift !!!!!!!

 

[joe raptor]

Thanks brother !

 

[FiveLeeter918]

glad to hear!

 

[Just sho up]

That’s supper exciting

 

[joe raptor]

My mechanic show me how close is the second hole on the sway bar to the frame it is , so he used the first hole instead and still very tight on turns, I'm very happy with the results !!!

 

[FiveLeeter918]

Are you lowered? The test cars at the facility all cleared fine but were stock ride height. I still need to get some measurements done to get specifications for the adjustment end links so that us lowered cars can utilize the more aggressive hole, but given the tightness with even the first hole I'm not sure I could handle the second hole haha.

 

[Nova]

but given the tightness with even the first hole I'm not sure I could handle the second hole haha.

I couldn't resist lol

Sent from my SM-G986U using Tapatalk

 

[FiveLeeter918]

I couldn't resist lol

Sent from my SM-G986U using Tapatalk

Lmao touche'

 

[joe raptor]

Yes I'm lowered with the H&R springs

 

[Ecoboost_xsport]

Can you elaborate ?? I was on my back and jack stands too !!!!!!! Do you have a video ? Just curious !! I tried every possible way and I couldn't snake the MOTHER FLOWER out !!

I know you already got it done, just wanted to show the video I made, in case it can help anyone else. Note how I removed the stock one from the vehicle. It's also an Explorer Sport, but it should uninstall/install similarly:

 

[joe raptor]

does anyone know the correct part # for the rear sway bar links ?? I heard you have to go longer than the stock one !!

 

[Autox4fun]

does anyone know the correct part # for the rear sway bar links ?? I heard you have to go longer than the stock one !!

I run a Flex, Megan coilovers and did have touch down issues, popped one side of my factory end link. 10mm stud, and roughly 6 inch is what I switched to. I sent pictures and measurements into Joel at customer service at Whiteline.

 

[fordfanstan]

I run a Flex, Megan coilovers and did have touch down issues, popped one side of my factory end link. 10mm stud, and roughly 6 inch is what I switched to. I sent pictures and measurements into Joel at customer service at Whiteline.

Could you post here what you used?

 

[Autox4fun]

Could you post here what you used?

https://www.ebay.com/itm/New-Front-...48ada017664c2ea33c29|ampid:PL_CLK|clp:2334524

 

[Just sho up]

Are these still available and if so who do I reach out to for an rfq.

 

[FiveLeeter918]

Are these still available and if so who do I reach out to for an rfq.

Planning commercial launch in April, but reach out to Joel at Whiteline to see if they have any more from the initial run.

 

[Just sho up]

Planning commercial launch in April, but reach out to Joel at Whiteline to see if they have any more from the initial run.

Lee you are absolutely the man! It’s always been such a pleasure working with you. Thank you for all you bring to this community.

 

[FiveLeeter918]

Lee you are absolutely the man! It’s always been such a pleasure working with you. Thank you for all you bring to this community.

I do what I can with my limited resources

 

[joe raptor]

will this links are for the front? or the rear ?