So what did you do to your SHO today!?

[Kelly Padfield]

I added LED licence plate lights and all LED interior lighting.

 

[SHOdded]

Got part numbers to share?

 

[Kelly Padfield]

I came across another post where a couple members recommended these:
http://www.ebay.ca/itm/251198124444?_trksid=p2060353.m2749.l2649&ssPageName=STRK:MEBIDX:IT
They are a nice crisp white light and they come with a year warrenty. So far I'm happy with the lights.

 

[SHO T1M3]

Bought some Plasti Dip to do my wheels tonight. "Blurple" for the base coat and "Sapphire blue pearl" for the top coat. Here are some pics in direct sunlight and in the shade.



Sent from my SM-G930T using Tapatalk

 

[mmh64]

I came across another post where a couple members recommended these:
http://www.ebay.ca/itm/251198124444?_trksid=p2060353.m2749.l2649&ssPageName=STRK:MEBIDX:IT
They are a nice crisp white light and they come with a year warrenty. So far I'm happy with the lights.

I have the same light set. I'm also happy with them. Something strange I did notice however. When the lights are out the center dome light in the back seat and the two center dome lights (driver and passenger side) have a faint glow to them. Not at all noticeable unless you realy look at them. It hasn't caused problems and I actually like being able to glance up and see the dome light when I'm driving. Before I would reach up and accidentally open the sunroof all the time. Still something strange that I have no explanation for.

 

[SHOdded]

I think you have to have one incandescent in the circuit to prevent that or add a resistor.

 

[mmh64]

I think you have to have one incandescent in the circuit to prevent that or add a resistor.

Thanks SHOdded, I didn't know that. Would anyone know the ohm value for the resistor?

 

[SHOdded]

I will have to check the writeup on it and post back here.

 

[SHOdded]

Cant find it right now, I will keep looking. In the meantime, heres a howto video on adding the resistor

1/4w 470OHM resistor.

 

[Kelly Padfield]

I want to say 140 ohm for some reason but I can't remember where I read it.

Sent from my XT1097 using Tapatalk

 

[Kelly Padfield]

Nvm I found this on one of Shodded's Posts.

How to Install LEDs with Resistors in the 2015 SHO Rear Dome Light (thanks to Evilcartman )

Ford Taurus LED Dome Light Install

Ford Taurus LED Dome Light Install - How to add a resistor to get it to work. I used a 1/4w 470OHM.

Sent from my XT1097 using Tapatalk

 

[SHO T1M3]

Finally finished up the wheels! Can't wait to get those calipers done now!
Stock

Plasti Dip™ Blurple - base coat (4 coats)

Plasti Dip™ Sapphire Blue Pearl - top coat (3 coats)

I'll post another pic tomorrow in the sunlight!

Sent from my SM-G930T using Tapatalk

 

[SHO T1M3]

I expected a little more gloss but the pearl isn't bad



Sent from my SM-G930T using Tapatalk

 

[SHOdded]

Nice work. Makes it stand out for sure! Makes me think you should dip the whole car, and if you like the results, have it professionally put on (they bake it on) so it will last even longer.

 

[SHO T1M3]

Nice work. Makes it stand out for sure! Makes me think you should dip the whole car, and if you like the results, have it professionally put on (they bake it on) so it will last even longer.

Thanks! It was my first time plasti dipping also lol. I'm considering plasti dipping graphics from some FPV cars I've seen. In the same color of course As well as the emblem (Ford Performance Vehicles - Australia).
Like these


I'm just a little nervous about how easy/difficult it is to peel off. I put 7 coats total on the wheels. I've heard the more coats, the easier it is to remove.

Sent from my SM-G930T using Tapatalk

 

[SHOdded]

Yup you should be good. Tiny spots might need to be redone after a while, especially if you go through high pressure car washes.

 

[Sholab1]

Just added Uleashed 91 octane toon for non mods. God what the version with plugs, temp and 3 bar must be like



Sent from my XT1254 using Tapatalk

 

[2012korn]

^you're only 150 bucks away from finding out........

 

[StealBlueSho]

$150 for the supporting cast..... Then $600 for DPs...$1300 for exhaust...$450 for meth.... Dyno tuning afterwards.... Yup... that's what happens when you "find out" >:-D

Sent from my Nexus 6P using Tapatalk

 

[2012korn]

Or if your lucky like me....300 for downpipes with under 5k on em.