Search results

  1. Devin

    What now?

    I can't get a break on this car. Oh wait, I guess I can.
  2. Devin

    Poor performance

    My car has been running quite rough for a month or so and I pulled the codes and got these stored on KOEO: 177 181 219 Looks like I may have a bad O2 sensor, which is easily fixable, but the SPOUT one throws me off. Would the O2 sensor cause that code?
  3. Devin

    Engine coolant level sensor

    LMR has repro 90 - 95 Mustang coolant level sensors for the overflow bottles. I just ordered one after their being out of stock for a few months. Should work in our situation but I will report back on if it does or not. https://lmr.com/item/LRS-10968A/90-93-Mustang-Low-Coolant-Sensor
  4. Devin

    Difference between end links

    I noticed there are two types of end links available, a solid metal bar and thicker, plastic ones. Is there a suggested style?
  5. Devin

    Won't turn over

    I spent some time and money working on this myself but am getting to the point where I am stuck. A couple weeks ago I was leaving a store and had a hard start condition where I turned the key and got a rapid clicking noise, and then the car turned over and started. Fast forward a few days...
  6. Devin

    Drivers window detached from regulator

    I've been getting a noise when having the window descend for a few weeks. It would make a thunk sound when it first began to descend. Today, at least the leading edge of the window detached from the regulator and it was a struggle to get it closed. I'm going to open the door up tomorrow to take...
  7. Devin

    EATC Replacement from Continental?

    Does anyone know if the EATC out of a 1989 Continental would work in a 1990 SHO?
  8. Devin

    Water pump dead already?

    Been leaking coolant for a couple months now, almost immediately after changing water pumps. Finally took the timing covers off and it looks like it is the weep hole. Is there a way to install this improperly that would cause that, or is it just a dead pump?
  9. Devin

    Well this sucks

    Started hearing a screeching sound about a week ago once in a while during startup. Looks like the starter is eating my flywheel. Does it look like it needs to be replaced?
  10. Devin

    zoomlater is a prince

    He noticed that I had an upcoming heads job and offered a great price for a full set of seals and gaskets. We met up and made the exchange and he even threw in a harness. Great person to deal with.
  11. Devin

    What weight of oil for a cam position sensor?

    I always forget to change the oil on my cam position sensor. Try to ignore all the old oil on everything else. Heads are being done soon. There was a small pool of oil inside the head where the sensor mounts. Is that the sign of a failed cam shaft seal?
  12. Devin

    Fred Meyer SHO meetup?

    I mean, works for me!
  13. Devin

    Idle issues

    I recently switched out my idle air bypass valve IAB/IAC/ISC with a new Delphi CV10140 due to some issues with my idle hunting and sometimes settling at 2000 RPM. Now it seems my problems are worse. When I start the car it idles around 2400 for a few seconds then slowly drops to 1500, and after...
  14. Devin

    Ring job?

    I'm burning a bunch of oil. No real puddles, although I definitely have built up dirt/oil under the engine, and I know the oil level sensor gasket is leaking a bit... but I am putting in about a quart every 500 miles or so. I park in gravel, but I don't seem to leave puddles. To me it seems like...
  15. Devin

    Door locks issue, need diagram

    I have some annoying door lock issues. Currently I cannot actuate the door locks on the driver front, and passenger rear. I changed out the rear actuator and it still does not work. Tested it with my bench tester and the actuator functions. This got me thinking it was wiring. I need to look at a...
  16. Devin

    Gen 1 SHO logo for wheels

    I'm looking at Etsy to get a vinyl sticker to put over the center caps on my wheels. Hoping to find a Gen 1 logo, but not having much luck finding anything. Had anyone else done this?
  17. Devin

    Rivet with large flang3 for rear door

    I had to replace the acutator for my rear passenger door on the 90, but to get the mechanism out I had to drill out a rivet holding the bellcrank, and to reinstall I think I'll need another rivet like the one I drilled out. Any idea how to find these?
  18. Devin

    Leaking caliper

    Does this look fixable? The fluid is not coming out from the hose connection, it looks like it is coming out of the area with the emergency brake spring. I'm wondering if I have to go get a rebuild. Ever see this before?
  19. Devin

    End link stupidity

    No idea why I did this many moons ago, but both sides of my rear end links aren't attached properly. It looks like I don't have enough bushing or thread to tighten, and the bottom looks like it is at the wrong angle entirely. Any ideas what went wrong here?
  20. Devin

    Tranny job coming up soon. CM, Spec or South Bend

    Stock '90 SHO. Don't really look to be adding power now, or possibly ever. I have a CM stage 1 clutch I got way back when Midwest SHO was around, and I am looking to pull it down on a friend's rack and do some maintenance. Haven't really paid much attention lately, but should I stick with the CM...

Latest posts

Forum statistics

Threads
107,086
Messages
1,181,304
Members
16,152
Latest member
lapochkarr

Members online

Total: 403 (members: 1, guests: 402)

Share this page

Back
Top