Search results

  1. G

    '92 ecu

    I installed a '90 3.0 w/o egr in my '92 w/egr and of course the check engine light is on. The codes it shows indicated low egr flow. Will installing the ecu from the '90 make the codes go away along with the light?
  2. G

    Mtx assembly help

    I just welded my diff. up and I'm looking for any info about reaasembly. All tips and hints will be welcomed. I found some really good disassembly info on another website, but using it reverse isn't working to well.:nut: Thanks in advance
  3. G

    To weld or not to weld

    I've searched and found many threads that are pro welding of the differential pins and many replys to those threads that say just changing the roll pins is good enough. I've have to change the trans in my car for a blown diff pin. I don't want to lose another trans, so do I weld the diff pins or...
  4. G

    Old 3.0

    I'm scrapping an old 3.0. It spun a bearing, so the crank and 1 connecting rod are toast. If anyone needs anything off of it let me know. It's complete from the intake down. Come take what you want ( read free ). It's going to recycling next weekend. This engine went thru 2-3 quarts a week, so...
  5. G

    oil pressure

    i just installed a guage for oil pressure in my car; Does anybody have the specs for the correct oil pressure? My manual does not have the low/high limits. With new rod bearing, my car, at idle, has 10-15 psi. Is this okay?
  6. G

    valve stem seals

    Before I install the new engine in my car, I want to do the stem seals; has anybody ever changed the seals without the Rotunda tool kit? Does anybody rent these tools?
  7. G

    oil pump

    2k miles ago I put in a low mileage eng. in my car (110k). When I put the engine in, we replaced the rod bearings. After we started using the car again, the low pressure light would come on randomly and then go out, it didn't matter what rpm it was at. Changed the pressure sensor and the problem...
  8. G

    EGR question

    I recently installed a '89 engine in my '92 SHO. My '92 was equipped with an EGR setup, the '89 was not. I'm not planning on using any of the EGR stuff except the exhaust manifold, which I fabbed a blocking plate for. My question is this: What do I do to make sure I don't end up with a CEL? Is...
  9. G

    Another timing belt question

    Long story: I am in the process of installing another engine in my car. While the engine is on the stand I decided to put a new timing belt on. I took the old belt off after lining up the timimg marks on the balancer and the cam pullies. I went in the house for a short while, came back and slid...
  10. G

    engine harness

    Is the wiring harness on a 1990 3.0 the same as a 1992 3.0? I'm changing engines this weekend, and don't want to find out I have to swap harnesses after the engine is installed. :nut:
  11. G

    3.2 into a mtx

    I am swapping a 3.2 into '92 mtx. Am I going to be able to use the acc. from the 3.2? How about the engine wire harness? Does anything need to be removed,added,drilled,filed,shimmed to the 3.2 to fit on to the mtx? Thanks for your help :thankyou:
  12. G

    Rod Bearing P/n's

    i'M TRYING TO FIND ROD BEARING IN MY AREA, BUT ALL THE PARTS STORE SAY THEY NO LONGER ARE AVAILABLE AS THEY DON'T SHOW ANY P/NS. DOES ANY ONE KNOW OF ANY P/N'S SO I CAN GIVE THEM TO AZ , NAPA, OREILLY'S?
  13. G

    Code 219?

    What is a code 219 mean? SPOUT signal defaulted to 10 degrees BTDC/ SPOUT circuit open. Also have code 213; spout circuit open?
  14. G

    '92 SHO fan issues

    I just picked up a '92 SHO and have a couple of problems. 1. The heater blower will not shut off. I changed the EATC control head because the buttons were broken, also thinking that this would shut the fan off; no joy. When selecting the "off" button, you can hear the vacuum moving doors...

Latest posts

Forum statistics

Threads
107,087
Messages
1,181,313
Members
16,153
Latest member
lapochkarr

Members online

Total: 555 (members: 1, guests: 554)

Share this page

Back
Top