Quaife, plus so much more, Rollbacks on 6/20

[Ghost93]

Black 93 console, atx but commonly used for an mtx. Great shape, a small scratch on the one side(pictured).$150 shipped

[/IMG]

[/IMG]

[/IMG]

[/IMG]


Sho Shop Aluminum Flywheel, used, fresh Blanchard grind on insert-Sold

Hoosier R3S04 225/50 on slicers, 3 have good tread, one tire has a spot to the cords from a panic stop(see pics) - sold


Nitto 555R 225/50 drag radials on slicers, hardly used, $175 + shipping

[/IMG]

[/IMG]

XS Power Water to Air Intercooler with huge C&R heat exchanger, pieced this together to go with a Vortech on the Sho. The Heat exchanger fits in the opening on the bumper of the gen II, but the AN fitting on the back will probably have to be relocated to the side(see pics)- $300 + shipping

[/IMG]

[/IMG]

[/IMG]

Accel 30# injectors modded for the Sho (pintle caps added), plus 2 extra, still need modded rails- $150 shipped

Modded rails for Accel injectors, done on a mill, and the rails are polished-$75 shipped

HKS blow off valve from Sho Shop kit-$50 shipped

Aluminum water pump pulley from Sho Shop UDP kit- Sold

Non Vaps rack, rebuilt with new inner tie rods, with new Moog outer tie rods in box- $150 shipped

Sho Shop torque limiters, never used, powder coated chrome- $125 shipped

NOS from Ford chrome window wiskers, in box from Ford, full set, all four doors- $150 shipped

3.2 Purple top injectors, 87k-sold

Rear Tokico Strut cores, no rebound and are in rough shape, didn't know if someone would want them for a warranty or as housings, before I throw them away-Make offer

3.2 Cylinder Heads, off an engine with 87k, could use a cleaning-Make Offer

Any 3.2 stuff, like timing covers, tensioners, brackets, let me know what you need, I should have it.


I'm sure I'll find more to add, any questions about anything, please ask. Can get pics of anything upon not pictured, or more detailed pics upon request. Would consider trades. Mainly deal in Paypal, but can work with something else if necessary.

Kevin Mitchell
Email= [email protected]
Phone= (815) 871-1361

 

[Ishodu]

Approved and email sent.

 

[Ghost93]

Sale pending on the water pump pulley.

 

[rocket455]

pm'd for injectors sir

 

[matasho]

bumpski

 

[blue2ndgen]

Does the flywheel have an aluminum insert? Do the drag radials come as a set of 4 or 2?

 

[SinisterSHO]

for what its worth, I believe Kevin is trying to make the Convention, if not, I will be there and could bring any of these parts there for pick up.

 

[Ghost93]

Does the flywheel have an aluminum insert? Do the drag radials come as a set of 4 or 2?

I believe the flywheel is sold, but it is a steel insert. The drag radials are a set of two for the front.

 

[St Louis SHO]

Make me a deal on the Quaife, Kev.

 

[Ghost93]

Flywheel is gone.

 

[Jh8990]

pm sent

 

[Ghost93]

Pulley is sold, some new parts added.

 

[rocket455]

pm sent

 

[Ghost93]

Bump, lowered prices, hoping to get to the convention. If I don't get any offers on the hoosiers and D/Rs, I might separate the tires from the rims and sell on ebay/ craigslist. Would anyone be interested in slicers? Otherwise their going to the scrapyard.

 

[hamburglar]

can i get a picture of the door wiskers?
they contain the whole chrome piece that runs below the window correct?

 

[Ghost93]

[/IMG]

[/IMG]

[/IMG]

Yup, they are the pieces that run along the top of the door. I bought them back when I had a 93, but now have a pair of 95s, which have the black trim. They are still in the packaging from Ford, and cost a lot more than I'm asking, and I'm not even sure they are still available.

 

[hamburglar]

just a general question
how hard are they to put on?
I'm sure not too bad, but I have never done anything with these parts

 

[Ghost93]

There is two studs, one on each side. The rear nuts are fully exposed by opening the door, and IIRC you just need to take off the door panels and possibly the mirrors for the front.

 

[Shopower400]

PM snet..

 

[Ghost93]

PM snet..

Replied