Greg1991Plus
New Member
I've owned 4 SHO's and this is one I've had about 3 years and it's time to let it go. I knew the previous owner and he did all the subtle mods to the car. It has all the good plus features with the ABS bulge hood, rod shifter, and original rear deck spoiler.
It still has shiny original factory white paint, with assorted small dings and scrapes but shows very well overall. Not a spec of rust at all anywhere on body. The interior is black full leather and is also very nice also with just a split in the drivers seat bolster and on top of the rear seats and one seat bottom.
The car has 173K miles, but just 3,000 miles since going through the motor--heads were removed, valve job, valve seals, cam seals, couple guides, light surfacing were all done. Valves were adjusted to middle of clearance specs. Ford head gaskets were used. The block got a lite bottle hone and all pistons had new Ford rings installed. New intake and exhaust gaskets, new timing belt and crank position sensor. Water pump also recently replaced along with idle air control valve. The rod bearings were replaced along with checking the main bearings. They were all retorques with a Snap-On digital torque wrench.
Car runs and drives great, clutch is good, front brake pads and rotors are new, has polished slicers with 225/55/16 tires. The AC has been blowing cold and sometimes not so cold so the charge is getting low. The engine is making a rattling noise on top which may be the timing belt tensioner and I have the part on order and will be installing it.
All 4 struts were also recently replaced.
These are the mods done to the car:
96 Big Brake upgrade
Walbro fuel pump
Performance Plus y-pipe
Summit turbo mufflers
Welded in subframe connectors
Front and rear strut tower braces
Sony sound system with CD changere in trunk
Police grille
Window tint done by new car dealer 2 years ago, cermaic film, 20% rear, 35% front, windshield band too.
The car is in the San Diego, Ca area.
New price to move it quick----------------------$2,500
Email: [email protected]
Thanks,
Greg
Here a pics inside grage and new outside pics:
It still has shiny original factory white paint, with assorted small dings and scrapes but shows very well overall. Not a spec of rust at all anywhere on body. The interior is black full leather and is also very nice also with just a split in the drivers seat bolster and on top of the rear seats and one seat bottom.
The car has 173K miles, but just 3,000 miles since going through the motor--heads were removed, valve job, valve seals, cam seals, couple guides, light surfacing were all done. Valves were adjusted to middle of clearance specs. Ford head gaskets were used. The block got a lite bottle hone and all pistons had new Ford rings installed. New intake and exhaust gaskets, new timing belt and crank position sensor. Water pump also recently replaced along with idle air control valve. The rod bearings were replaced along with checking the main bearings. They were all retorques with a Snap-On digital torque wrench.
Car runs and drives great, clutch is good, front brake pads and rotors are new, has polished slicers with 225/55/16 tires. The AC has been blowing cold and sometimes not so cold so the charge is getting low. The engine is making a rattling noise on top which may be the timing belt tensioner and I have the part on order and will be installing it.
All 4 struts were also recently replaced.
These are the mods done to the car:
96 Big Brake upgrade
Walbro fuel pump
Performance Plus y-pipe
Summit turbo mufflers
Welded in subframe connectors
Front and rear strut tower braces
Sony sound system with CD changere in trunk
Police grille
Window tint done by new car dealer 2 years ago, cermaic film, 20% rear, 35% front, windshield band too.
The car is in the San Diego, Ca area.
New price to move it quick----------------------$2,500
Email: [email protected]
Thanks,
Greg
Here a pics inside grage and new outside pics:
Last edited:
you have nice SHO's 
That is my all time favorite SHO!! Its absolutely beautiful!!! That car wont have any rust on it. I bet its easy as **** to work on. Good luck with the sale!! If i didnt already have mine i would be calling you to talk about it.
