Search results

  1. D

    Back to the Dyno for 600

    Well, I recently went back to the dyno in my quest to make over 600 whp. This journey has had its hurdles for sure, but my setup now seems to be the best so far. Last week I brought the car back to the same DynoJet dyno where the car made 530 whp. Back then I was running the GH Gen3R turbos at...
  2. D

    Anyone tuned with over 25 psi using the SCT X4???

    I’m having an issue trying to get my tune to reach the commanded boost level my tuner is inputting. We are not sure if there’s a limit that the ecu will allow for boost. We know the SCT X4 will only read up to 22.47 psi. After that you measure boost through map sensor at wot. The tuner is...
  3. D

    My experience with TurboBay Performance

    Good Morning, I'm going to let everyone know my experience with having TurboBay Performance modify my factory Ford turbos to their stage 4 setup. Here's a short back story to my car. I own a 2013 SHO P/P with a fully built motor (CSS Block, JE pistons, Raptor crank, Boostline rods, XDI...
  4. D

    Turbo oil feed line filter. Remove or not?

    Anyone out there remove the turbo oil feed line screen filter? I’m curious because I had a turbo shaft snap on custom built turbos. The shop stated possibly oil restriction could have been the cause.
  5. D

    Zero Wastegate and P0299

    So today I set out to datalog the car as Brad sent me another tune. During the datalog I notice the car felt slower than normal. Once I got home I reviewed the log and noticed the car initially made the desired amount of boost for approximately 7 seconds then my waste percentage dropped to zero...
  6. D

    GH Gen3R TURBOS FOR SALE

    Up for sale is a set of GH Gen3R turbos with approximately 800 miles on them. First 500 miles on these turbos were at very low boost due to strict limits by my engine builder. They are in excellent condition. My car made 530 whp with these turbos at 22 psi. I’m only selling because I’m now...
  7. D

    Help with Forscan

    Today I was trying to use forscan for the first time. Got everything downloaded and connected to my 13 m’ SHO. But Forscan wants the strategy number which I don’t have/know or calibration name. I tried to pull up the strategy number using my Sct tuner but it says strategy not found. Can I just...
  8. D

    Need help with Codes P0625 and P065B

    I took my car out today and had my charging system light come on. So while I was driving I switch my aero force gauges to monitor the voltage and it was bouncing around from 13.6 to 14.0. I ran the codes and got P0625 and P065B which are related to charging. Once I got home I tested my battery...
  9. D

    New turbo setup for more psi!

    So last year I was able to finally get my 13' PP SHO all back together after a long time having the engine built after catastrophic engine failure. I opted to have RMB Motorworks build me a stage 2 shortblock with boostline rods and custom coated JE pistons. It also came with the CSS to help the...
  10. D

    Fuel It ethanol sensor power???

    Is anyone running a Fuel It ethanol sensor and if so what fuse did you utilized to get 12V key on power from? Thanks for looking!
  11. D

    Anyone ever get a Code P2197?

    I just got a P2197 code with my 2013 Sho pp. I looked it up and it refers to a O2 sensor on Bank 2. But all my O2 sensors are new from Ford with less than 700 miles on them. I guess one could have gone bad. But did a little research and it also could be a vacuum leak. Anyone ever get a code...
  12. D

    Help with replacing LPFP

    I'm gonna be replacing my LPFP with a new pump that I had modified with the Hellcat 525. I've never replaced one on a ford and I saw one video online where there's a clip under the top portion of the pump that looks almost impossible to get off without a special tool because of the limited...
  13. D

    Any using AKD’s coupler and clutches?

    I’m curious if anyone is using AKD’s coupler and clutches for the RDU. And if so can you give me some feedback on it. Thank you for looking …
  14. D

    Nitto NT555ll on 20x8.5 wheel

    Has anyone mounted a Nitto NT555ll 275-40-20 on a 20x8.5 wheel? I’m gonna be buying some Nitto’s but not 100% sure they fit properly on my Rovos Durban 20x8.5 wheels. If they don’t fit I may have to buy the same wheel in a 10” wide wheel. But that’s a last resort. Thank you for looking
  15. D

    KAM reset and crank relearn

    Hey guys My new built engine is almost done and ready to be installed. I'll need to do a KAM reset and Crank relearn procedure prior to the first start up. Is there any special instructions that need to be completed prior to completing these two procedures?
  16. D

    What’s the fastest FULL weight SHO?

    I’m curious if anyone knows of the fastest full weight SHO quarter mile time. Also what’s the highest whp for our platform to date. Thanks for looking...

Latest posts

Forum statistics

Threads
107,085
Messages
1,181,300
Members
16,152
Latest member
lapochkarr

Members online

Total: 373 (members: 5, guests: 368)

Share this page

Back
Top