Search results

  1. J

    clutch rattle

    I have 92 sho with 116k with second cluth(Put on at 86k)The replacement was stock valeo and bearing. I hear a rattle noise from trans area, but when I push in clutch the noise is gone. When I shift it's not smooth anymore...... Jason
  2. J

    torque bar bushings

    It's the top half of the bushing also not the bottom. Is my control arm not sitting right? The control arms are moog and the struts are gabriel complete ready mounts, am I doing something wrong? jason
  3. J

    torque bar bushings

    anybody Nobody can answer this?
  4. J

    Replacing Hub/Wheel bearing/Knuckle

    oh axle nut yes and you need a puller to push axle out......get the book man...has torque spec for you also.
  5. J

    torque bar bushings

    What is the trick to getting front torque bar bushings seated in subframe. The clevites inside subframe I cannot for the life of me get rid of 1/8 in gap between bushing and subframe...................I have taken apart and put together so many times with same results........ jason 92 not stock
  6. J

    Replacing Hub/Wheel bearing/Knuckle

    As for removing knuckle get chilton book, very easy and dirty remove rotor and brake caliper remove tie rod end from knuckle looosen pinch bolt to knuckle remove ball joint to knuckle pinch bolt pry ball joint off knuckle or rmove subframe/balljoint pinch bolt pull knuckle off strut-oh abs...
  7. J

    Replacing Hub/Wheel bearing/Knuckle

    The autozone one is hub and bearing together.....,make sure to check length of studs as the units I bought had shorter studs. I finished job-all day and go to put tires on and lug nuts would barly hold on. Went to autozone and they gave me longer studs-had to punch them out and put new ones...
  8. J

    locking lug nut key

    All you have to do is take a four way tire iron find one thats snug, lightly pound on lock and turn,at leat thats what I did and they were tight. Then get some regular nuts, those locks are pointless. jason
  9. J

    oil problem

    the seals ared clean the oil pan seal clean, no oil leaks on y pipe-clean-only on trans and oil level sensor. I don't know.
  10. J

    oil problem

    I got the car with 106k on it it has 115k and is ready for 120k or 2nd 60k. It did consume oil abot 1qt every 1k but is double now! It does seem to blow smoke while shifts are happening I/m told and it's very dark smoke? What is the oil on trans and why does it only leak while driving. I smell...
  11. J

    oil problem

    I have an oil problem. My sho is eating oil 1 quart every 500 miles!!! It does not leak on the ground....not a drop. After driving I can see moisture around trans and the sensor on back top of oil pan, but does not stain ground at all....not a drop!!! Is this a pressure leak.....help me...
  12. J

    ABS unnecessarily kicks in while turning sharp

    its the wheel speed sensor, been there. jason
  13. J

    Rear Motor Mount

    I'm doing this in my driveway. How would I do this without a hoist? :help:
  14. J

    Rear Motor Mount

    Does anyone know procedures for removing and installing rear motor mount? :oogle:
  15. J

    front suspension

    OK. I just installed ready mount gabriel struts, complete, new control arms, all new bushings/poly and I have a problem. The right side is 1/2 in higher then left.....what do I do to fix this? jason 92 yes modded
  16. J

    Knocking noise from inside the Intake

    my crank pulley has a weird wiggle also.....sho shop pulleys.....how do I fix, now I am scared....... jason 92 with mods
  17. J

    speedo cable

    Is there a trick to sealing the speed sensor that fits into the top of mtx trans? I have fluid leaking out it and I have made sure it is screwed in tight....and does this cause the speedo needle to bounce and make a noise? How do I fix? jason 92 mtx
  18. J

    Hungry?

    Don't girls drive those cars........
  19. J

    Hungry?

    who is this looser anyway? I'm waiting for my re sized fuel rails to arrive and 48lb injectors and 9 psi t trim blower is waiting to be put on.......I will sho you the way then...........
  20. J

    The continuing chronicles of the front clunking/popping noise in my '89. Help a SHO.

    All I can say you guys is that I changed tie rods, struts, springs, links, and the last thing I changed on my car after four years of owning was hubs and wheel bearings. The car sticks to the ground like super glue. the slight hesitation I used to feel is gone. My arms hurt like ****...

Latest posts

Forum statistics

Threads
107,088
Messages
1,181,317
Members
16,153
Latest member
lapochkarr

Members online

Total: 378 (members: 3, guests: 375)

Share this page

Back
Top