Search results

  1. J

    Code 542 542 (O,M) Fuel pump open, bad ground or always on what could cause it?

    like it says what is the usual cause of code 542 (O,M) Fuel pump open, bad ground or always on - - Power / Fuel Pump Circuits? thanks guys i just did my cps sensor haha that was a ***** so i wana get her runnin tip top now
  2. J

    code 211 bad crank sensor?

    code 221 Ignition PIP signal was erratic or missing is this the usual code for a bad crank sensor? the sensor was changed only a year ago by my friend before i got it i just wana make sure before i go and change it thanks joe
  3. J

    car just died...think it cloged and leaky injectors have a few ?

    ya my car is a lil messed up yesterday i filled my car up but it was really low close to E. after i filled it i drive and parked the car and it cut out i tryed to restart it but it would not. i looked around and pressed the check valve on the fuel rail to see if there was fuel and there was...
  4. J

    3 wires conect the speaker amp to the sub amp..which wires are which?

    ya i see there are 3 wires in the conector im sure that 2 of them are for the speaker preout to the sub but what is the other wire for? is it a remote on wire? im looking to run the stock int speaker amp and run a fosgate sub amp. can i use the wires coming out of the stock amp as...
  5. J

    power rating of stock int amp for each channel and sub amp

    like it say...how powerful are they i would like to know if it is worth keeping my amp or just runnin off the head unit. i will also loose my sub if i do this and i dont want to thanks guy joe
  6. J

    replacment speaker for factory sub

    ya it soulds like its blown is there a replacment speaker that i can get for it? how big is the speaker and what rms if posible...2 or 4 ohm thanks guys joe
  7. J

    best swaybar setup (sizes front and rear) for drag racing

    i got my 92 sho which if im correct has a 24mm front and a 23mm rear bar just wondering which is the best for straight line grip for the fron wheels with out getting very sloppy in the corners? thanks alot guys joe
  8. J

    i adjusted the clutch cable and now clutch does not seem to engage all the way helpme

    ya i adjusted the quad and not the tranny does not grind into rev but now it does not wana chirp second gear at all now and it chirped it hard before i adjusted it anyway to unadjust the cable of fix my problem thanks joe
  9. J

    shifter when in gear wobbles side to side alot....fix?

    ya is there a fix for this or is that just how it is thanks joe
  10. J

    im getting a raptor shift light for the sho but what wire to tap in for signal?

    like it says in the title what wire do i tap for tach signal and i know its a 6 cylinder but which those coil packs how many cylinders do you set it to like on my ls1 it set to 4 cyl thanks guys joe
  11. J

    hey guys i got rid of that grinding in rev problem take a look inside

    hey guys i got rid of that grinding in rev problem i guess the clutch cable was stretched but the quad would not adjust by pulling up on the pedal...so i went under the dash and manually adjusted it 2 clicks now i have no problems getting into any gear when stopped or down shiftin nice and...
  12. J

    anyplace to pick up a stock power antenna?

    ya mine is busted and when you trun on and off the car you can here the motor stillrunning but the cord is broken where can i find one thanks joe
  13. J

    the bushings that conect my fron swaybar to my spindle are torn...part# for new link?

    hey just wondering what part number these and and what they are called thanks joe
  14. J

    what is the part# for the rod that comes off the side of the balljoint/control arm?

    what is the part number for the bushings on that bar that comes off the balljoint? i need to replace the ball joint and want to do that at the same time if a can thanks joe
  15. J

    hey is there a way to adjust the clutch cable?

    hey guys is there a way to? heres the deal...when the car is off the trans goes into gear fine but when running it has a lil trouble and it a lil hard to shift into second sometimes is this the clutch or something else? thanks joe
  16. J

    my shifter bounces around alot when i get on and off the gas what would cause that?

    like it says just wondering how to get rid of that thanks joe
  17. J

    bad plug seals...how to change?

    im new to the sho seen and i need to do the plug seals at least do i have to take the intake off? can i get away with just puting some sylicone on the plug seals and out everything back together or do i need to spend 100 bucks on gaskets? what else should i do while im in there...the...
  18. J

    how to change valve cover gaskets and plug seals?

    im new to the sho seen and i need to do the plug seals at least do i ahve to take the intake off? can i get away with just puting some sylicone on the plug seals and out everything back together or do i need to spend 100 bucks on gaskets? what else should i do while im in there...the...

Latest posts

Forum statistics

Threads
107,085
Messages
1,181,296
Members
16,152
Latest member
lapochkarr

Staff online

Members online

Total: 491 (members: 8, guests: 483)

Share this page

Back
Top