Recent content by NSR818
-
N
94 MTX 3.2 For Sale $7000 OBO
What is your availability for this coming holiday week? Im located in Los Angeles. Let me know. Thank you.- NSR818
- Post #5
- Forum: SHO Trader
-
N
3.2 ATX Will not run after engine install
Engine oil looked good when i drained it. I have disconnected the serpentine belt and ran the car to see if the noise will go away....the noise lessened but the its still present on the bottom end of the engine.....when i took the car for a test drive the oil light flickered...i believe the rod...- NSR818
- Post #9
- Forum: Gen 1 & 2 - Engine, Exhaust, Drive Line & AC syste
-
N
3.2 ATX Will not run after engine install
the white sho rolled out today...took it for a test drive....while at idle/warming up...it has a knocking/ticking sound at the bottom end.....the car is running on 100octane because previous owner put racing fuel in it...could it be just engine knock from wrong octane rating or bad rod bearing...- NSR818
- Post #5
- Forum: Gen 1 & 2 - Engine, Exhaust, Drive Line & AC syste
-
N
3.2 ATX Will not run after engine install
The SHO runs now.....timing was corrected and right plug wiring orientation (dont use chiltons manual for spark plug wiring orientation!)- NSR818
- Post #4
- Forum: Gen 1 & 2 - Engine, Exhaust, Drive Line & AC syste
-
N
3.2 ATX Will not run after engine install
Hello, Happy Holidays! I have a problem on my 1995 3.2 ATX. The car will not run during start up. I recently changed the Torque Converter so I dropped the motor. The car ran with a little bit of a misfire before I dropped the motor. I did the front and top 60k while the engine is out of the...- NSR818
- Thread
- Replies: 8
- Forum: Gen 1 & 2 - Engine, Exhaust, Drive Line & AC syste
-
N
1991 Plasti-dipped SHO (Flat-white)
The texture has a rough feeling.- NSR818
- Post #10
- Forum: Gen 1 & 2 - Wheels, Tires, Interior, Body, and Cos
-
N
1991 Plasti-dipped SHO (Flat-white)
Had the car for 10 years now, I was going to do a flat black theme.....but its a black car again...time to change the theme. The car was waxed before the dipping process ;)- NSR818
- Post #9
- Forum: Gen 1 & 2 - Wheels, Tires, Interior, Body, and Cos
-
N
1991 Plasti-dipped SHO (Flat-white)
Here is the finished plasti-dipped SHO. The process took 2 days in total. Its better than wax (Protection wise), and cheaper than vinyl wrapping the SHO. The plasti-dipped should last for a long time, depending on the weather abuse. The project cost me $350 (4.5 gallons of plasti-dip (black to...- NSR818
- Thread
- Replies: 17
- Forum: Gen 1 & 2 - Wheels, Tires, Interior, Body, and Cos
-
N
3.0 Engine Swap and Misc. Stuff Installed
Thank you. The SHO runs way better now. I was considering Gen 3 bushings but I didnt have enough time to order and wait for them.- NSR818
- Post #3
- Forum: Engine, Intake, Exhaust and Drive Line
-
N
3.0 Engine Swap and Misc. Stuff Installed
Installed new: Water pump, fidanza flywheel, clutchmaster stage 1, rear motor mount, mtx motor mount, top 60k, front 60k, rod bearings, valve stem seals, power steering lines, rack and pinion, starter, rear main seal, MTX output shaft seals, MTX fluid, A/C compressor, A/C o-rings, heater hoses...- NSR818
- Thread
- Replies: 2
- Forum: Engine, Intake, Exhaust and Drive Line
-
N
Post pics of your lowered ride!
Tokico/Intrax- NSR818
- Post #50
- Forum: Gen 1 & 2 - Suspension, Brakes & Body
-
N
Post Pictures of your car on the Auto-X Course!
http://www.youtube.com/watch?v=GPzCFWTQ6mA There's more at Matt's youtube. -
N
Post Pictures of your car on the Auto-X Course!
Thanks for posting the pics Matt! -Noli R. -
N
Post Pictures of your car on the Auto-X Course!
The officials told us to leave the windows down so that we have an easy way out when the car flips over. -Noli R.
