subframe bushings?

[llamaking122]

so today i pull out of a parking lot and it quit running. in the middle of rush hour traffic on a main road. me and a friend manage to push it back into the parking lot. we pushed it out of the way and we sit there and try to start it. i take the batt of then reattach it. so an hour later my dad shows up and a look for 2 secs and goes "your dis is unpluged". he plugs it in and starts right up. now i hit a bump and it cuts off again but this time i knew what it was so i plugged it right back in and got home.
now i looked at the rear two sfbs and theyre are toast. jack up the subframe and it moves. jack up the motor and it doesnt move (all very lightly)

 

[elarm1]

If your Front motor mount is torn, it can cause this same thing to happen. I don't think your sfb look that bad

*edit*

I DO think your sfb look that bad!

 

[llamaking122]

u sure?

 

[llamaking122]

either way its time for urethane mounts =DD
and alsfbs

 

[elarm1]

mounts and sfb's are expensive..... I would o with what is needed first. Alsfb are a lot cheaper than the gen 3's or stock but you might not like the nvh

 

[llamaking122]

mounts and sfb's are expensive..... I would o with what is needed first. Alsfb are a lot cheaper than the gen 3's or stock but you might not like the nvh

i dont give a hoot bout nvh i drive a SHO it makes all kinds of sounds XD

 

[firebat45]

I didn't notice much NVH at all. Maybe if you go from perfect condition stock mounts you'd notice a difference. I bet the ALSFB would be a NVH improvement over the current situation, and as a bonus would even keep the subframe from falling off!

 

[llamaking122]

I didn't notice much NVH at all. Maybe if you go from perfect condition stock mounts you'd notice a difference. I bet the ALSFB would be a NVH improvement over the current situation, and as a bonus would even keep the subframe from falling off!

haha yeah i dont think its the mounts cuz from what i saw they were ok but my dad knows better than i do XD. if someone can link the process to urethane the mounts plz. i lost all my fave. we have a store close by to get the urethane iirc

 

[elarm1]

When I did mine, I really didnt "notice" any nvh but I wouldnt go back to stock for anything! I love my reinforced mounts and alsfb!

 

[elarm1]

check ur pm

 

[FastAndFurious]

haha yeah i dont think its the mounts cuz from what i saw they were ok but my dad knows better than i do XD. if someone can link the process to urethane the mounts plz. i lost all my fave. we have a store close by to get the urethane iirc

Found it!

http://www.bonnefinstudios.com/kwb/automotive/tech/mounts.htm

Have fun!

 

[llamaking122]

Found it!

http://www.bonnefinstudios.com/kwb/automotive/tech/mounts.htm

Have fun!

thanks soooo much.

how hard is it to install alsfbs i have an impact and all of that so the tools arent really a prob.

 

[shotime1994]

If I were you I would drop your subframe sandblast it and paint it.

 

[llamaking122]

so if i go with 96/99 sfbs do they have to be SHO or can they be reg. what about taurii in general are they SHO specific

 

[llamaking122]

my dad said it might be a prob with the k member any ideas. i think its cuz a day or so before i had hit a steep parking lot at 15 mph bcz i didnt look before i turned in.

 

[zblackbeast]

... Looks to me like you need the recall kit to the floor of the car..

 

[llamaking122]

... Looks to me like you need the recall kit to the floor of the car..

its already been done...

 

[SHOmethewayhome]

just one more happy owner of ALSFBs and reinforced motor mounts here. DO IT!

 

[elarm1]

just one more happy owner of ALSFBs and reinforced motor mounts here. DO IT!

I'm with this guy

 

[llamaking122]

I'm with this guy

ya haha i might go to used 96 sfbs bcz im low on funds but if i can sell my ipod touch ima get some alsfbs.