Engineering drawings for trans gears

[Operation SHO]

I'm workin on building a new gear set but can't find the engineering drawings for them witch would make life so much easier. Any one know where I can find them I've looked just about everywhere.

Thanks!

-Doug H.

 

[frosho]

You do know there's a group buy going on for HD gearsets, right?

http://www.shoforum.com/showthread.php?t=100544

 

[Operation SHO]

Yea I'm aware but that's $5000 the raw materials for me to make my own are alot cheaper and it'll be fun to make them, well attempt to make then that is.

 

[somedude_001]

you could try shooting a pm to texan tony but don't be surprised if he doesnt give them up. i know i wouldent

 

[Off Road SHO]

I don't think anyone would do all the measuring of gears and then publish it for others to make money off it. If you have the ability to make gears, you undoubtedly have the ability to measure them up. Go for it and give the other designers/fabricators some competition.

Tom

 

[LJRuddy]

Make some syncros/blocking rings while you're at it!

 

[Off Road SHO]

Make some syncros/blocking rings while you're at it!

That right there would make you a Hundred-aire overnight. You'd be right up there with my company, a multi hundred dollar company, making tens of dollars every day.

Tom

 

[Operation SHO]

Hahaha I'll try to make everything so there is no weak link

 

[NovaSS]

just buy a quaife tranny. Even after you have a nice gear set you have a paper thin case that will flex and stretch.

 

[Operation SHO]

That's true but I'd rather take my chances and snot drop £8000 on a trans that is apparently universal lol

 

[shomethe$$$]

Yes, agree of Off Road, you'll spend a lot of time on reverse engineering the gears not worth it in my opinion, something I thought about myself, I'd much rather pay a company to do all the reverse engineering, that makes gears everyday and has had a good reputation for building race transmissions, in addition that will give you replaceable gears, perhaps even a warranty a believe, $5k is a good price for the group buy gearset.

 

[Ocnaj]

just buy a quaife tranny. Even after you have a nice gear set you have a paper thin case that will flex and stretch.

So you're saying that HD gears will hold 600+ horsepower but the MTX-IV case will fail?

What transmission is pictured?

 

[Operation SHO]

thats the universal fwd 6 speed tranny from quaife lol it translates to about $5100 american its advertised to withstand 750hp

 

[zach44102]

thats the universal fwd 6 speed tranny from quaife lol it translates to about $5100 american its advertised to withstand 750hp

ughhh what?

 

[Ocnaj]

thats the universal fwd 6 speed tranny from quaife lol it translates to about $5100 american its advertised to withstand 750hp

Is it universal enough to fit the SHO? That seems a little cheap...

 

[LJRuddy]

No straight cut, no care

 

[frosho]

I'm sure you'd have to make it fit, which would cost you more $$$.

 

[Operation SHO]

Is it universal enough to fit the SHO? That seems a little cheap...

i highly doubt it will fit a SHO, i was just checkin it out cause it was posted

 

[SHOspazz92]

I think that transmission is 15,000...not 1500... as its a Sequential Gear Box with straight cut gears.

-Sam

 

[Ishodu]

If I was going to go though the trouble of cutting new gears I would be making gear ratios diff as well. May as well. Good luck with the project. Btw make sure you look at a main shaft stripped as well there is a lot of work there to do other than cutting teeth.