Search results

  1. R

    power steering hose removal

    thanks Thanks for the valuable info this should make my task a lot easier.
  2. R

    power steering hose removal

    I am trying to remove the high pressure power steering hose according the helms manual you have to remove the rear motor mount and the pump pulley,then the pump it self. Do any one know a better way Anyone with experience please let me know. thanks, Curtis
  3. R

    y pipe options

    I have 160,000 miles on my factory y pipe ,I fear the old catlyst might destroy my engine. I was going to order from bittersweet sho until I saw the nightmares in vendor feedback. Is there any vendor with a good quality y pipe that is prompt in shipment after payment. Thanks
  4. R

    Pinch Bolts

    According to the Helms Manual you are suppose to replace the ball joint pitch bolts and nuts whenever they are taken loosen. Is this a safety issue or overkill.My worse fear is to have front collapse at interstate speeds(80-100). Thanks Guys for info.
  5. R

    Obsolete bearing for MTX / Quaife install

    She found it!!! It must be the last one. It cost me $60, but it saves me from having to have the shaft reground. Thanks again guys for all your help.
  6. R

    A/C Compressor Clutch...HELP!

    Auto Zone will rent a puller that screws into the hub with a bolt in the middle to push on the shaft. To use it with out pulling the compressor, you will need to cut one end off or cut a small hole in your inner fender to get to it.
  7. R

    I need to close my sunroof ASAP..Its raining. and button is broken

    Why didn't I think of that?
  8. R

    Obsolete bearing for MTX / Quaife install

    Good news! Bridget at Consolidated Transmissions said she found one in California. I got it on the way, but still have doubts until it's in my hand. Thanks for the help guys
  9. R

    I need to close my sunroof ASAP..Its raining. and button is broken

    It will get the motor out of time with the gears but you can fix that later.
  10. R

    Obsolete bearing for MTX / Quaife install

    Thanks, I tried Drivetrain.com and Bart said he had quit selling kits because the bearings are getting hard to come by, as I am finding out. Still waiting to hear back from Consolidated Transmissions, but they are looking...
  11. R

    Obsolete bearing for MTX / Quaife install

    Thanks I give them a try tomorrow.
  12. R

    Obsolete bearing for MTX / Quaife install

    Please Help! I am having to replace the input cluster gear shaft in my 91 SHO transmission due to missing teeth. In the process of this, I can not locate the bearing for the back end of this shaft. I know I am not the first person to have this problem so if any of you know who might have one of...
  13. R

    shoshop shipping

    I wanted to to know who shipps shoshops products ups or usps. I have a tracking number but it seems to be invalid with these two shipping agents. I would not be posting this if I did not hear negative feed back on this forum. I just spent $340 on a y-pipe I hoping that it shows up at my door...
  14. R

    A/C Compressor Removal

    My clutch on compressor is bad. I need to know can the compressor assy can be remove without taking out the alternator and radiator.
  15. R

    best startup procedure after rod bearing install?

    I would put some Mobil one 5w/30 in then crank it with the DIS plug disconnected.
  16. R

    New Problem: A/C full 45 PSI goes on then off

    According to the Helms ac troubleshotting section there should be at least 50psi in order that pressure switch to allow the compressor clutch to kick on I readed you have 35psi which is way to low.
  17. R

    Defeated by oil leak

    I spent three days making sure that the mating surfaces was clean of all traces of old gasket material,oil and anything else that would possibly cause poor sealing .
  18. R

    Defeated by oil leak

    The leak was there before I replaced the the valve covers and I forgot to mention that the front crank seal is also new. Is there some one in the DFW who you trust to work on your sho Sdpatt
  19. R

    Defeated by oil leak

    Well guys I Still have a mysterious oil leak thats leaking at what seems to be the above the pan gasket behind A/C bracket onto the frnt converter. I have replaced the oil pan gasket twice in one month.I replaced all three cams seals (which was not leaking at all).The valve cover gaskets are...
  20. R

    Mystery oil leak

    This oil leak is on the front side of the engine behind the compressor and alternator.its not the oil cooler o ring either.

Latest posts

Forum statistics

Threads
107,087
Messages
1,181,310
Members
16,153
Latest member
lapochkarr

Members online

Total: 355 (members: 5, guests: 350)

Share this page

Back
Top