Search results

  1. Johnbigdog

    Torque converter speed ratio behavior

    The pid: Tc slip dsd when it reads 1020 is a default "off" number. This is what the pcm wants. Tc-slip-act is the difference between engine rpm and turbine shaft speed. When tc-slip-dsd reads something other than 1020 you want to see a tc-slip-act within 10-15 rpm within a few seconds.
  2. Johnbigdog

    Turbo wastegate c-clip/e-clip

    I was changing the oil in the ptu and noticed my rear turbo's c-clip was M.I.A. I couldn't find a post on its size doing a few searches. I got a 5mm e-clip to fit. I dont know for sure if this is the corect size. I bought stainless steel assortment from the deep Amazon's. Hope everyone is...
  3. Johnbigdog

    Low on Coolest can't see leaks

    When the water pump is replaced, the intake is removed. The intake has coolant passages in it for the t-stat and heater hoses. Look in your engine valley for coolant. It may be hard. Lots of junk in there
  4. Johnbigdog

    Boost Question

    Look at/cor the c-clip that holds the wastegste actuator rod to the wastegste. They pop off.
  5. Johnbigdog

    Wiring diagram and/or Factory Repair Manual for 13+?

    Some libraries have acess to All data or mitchel on demand (aftermarket automotive repair manuals) or you can go directly to Helm who publishes the manuals for ford. The newer the car you can but CDs. Older cars have books.
  6. Johnbigdog

    I need a SHO BUTTERFLY wheel

    https://www.detroitwheelandtire.com/ford/taurus.html?cat=3441
  7. Johnbigdog

    Rear wheel bearing replacement

    Glad to see it worked for you. I hope you feel it was *esier* than trying to chisel it out, or pound it out from the back side.
  8. Johnbigdog

    2010 SHO, rear turbo seal replacement

    You can buy the ford workshop manual from helm. Looks like they no longer off the 2010, but do have a paper 2011: https://www.helminc.com/helm/Result.asp?Style=helm&Mfg=FMC&Make=FRD&Model=TAUR&Year=2011&Category=1&Keyword=&Module=&selected%5Fmedia= If you change to a newer model year you will...
  9. Johnbigdog

    Rear wheel bearing replacement

    This is as good as a place to put this i guess. If your replacing a front or rear wheel bearing, cut off 2 lug studs and pound them out. Get two 1/2 inch bolts that are full thread (higher grade prefered) and use the bolt to press out the wheel bearing from two spots on the kuckle like below...
  10. Johnbigdog

    Ford production runs

    If you haven't done so give Ford customer service a call (1800-392-3673 from google) there may be a process that they can follow to help you or your dealership get your part, maybe, a little faster.
  11. Johnbigdog

    Vacuum leak?

    That still makes sense because there is a larger check valves that holds vacuum in the booster and it also stops boost from reaching the booster. Speaking in general, if you turnnoff the car and press the brake pedal you usually have 1-2 presses before the brakes go hard. When you stall the...
  12. Johnbigdog

    Governor?

    The only exception is a ford performance tune. Boss mustang had a red key. That was oem supported I think? But I'm not sure if "ALL" dealerships will do that. And the SHO doesn't have a ford performance tune. Then the next step would be a Roush tune, but then warranty is a different subject all...
  13. Johnbigdog

    Vacuum leak?

    Ah! Now I understand better. Thank you for the image. You still have the main check valves back behind to prevent boost from going into the booster, but you have eliminated the ability of the system to create vacuum under boost or the possibility of the hissing noise! I kinda just thought...
  14. Johnbigdog

    Vacuum leak?

    Ha! Somewhat/kinda? My car hisses too. Some days its louder than others. Its been so long I can't tell you if mine didn't hiss. I wish I could tell you if it is supposed to his or not. I was hoping GotGrip would respond for sure. my option is that it shouldn't hiss if working CORRECTLY, but...
  15. Johnbigdog

    Part numbers needed for rocker panel retainers...

    my Google search says you might be looking at like a auveco 21522 and ford clip 6g1z-54101-82-a? They look familiar.
  16. Johnbigdog

    Part numbers needed for rocker panel retainers...

    My quick search this evening came up bare. Sorry.
  17. Johnbigdog

    Rear wheel bearing replacement

    I have a 16 P.P. the original wheel bearing part number is bt4z-1104-b There are two listed for my car by vin. I cannot tell you the difference of the top of my head. Sorry I'm to late.
  18. Johnbigdog

    Vacuum leak?

    The assembly itself is a vaccum on demand system that allows vaccum to the booster under instance where the intake is under vaccum. When the intake is under boost, the large check valves prevent the booster from poping and re routs the boost to the ejector (its a siphon) that uses the boost to...
  19. Johnbigdog

    Wheel stud replacement

    A 5 lb swing press will remove the stud from the hub. Next step is angle of the dangle to get it out and new one in. The new one is pulled in to the hub with something. It could be a sacrificial lug nut and some washers, or one may use the intended tool. 1st video I found exampeling a tool for...
  20. Johnbigdog

    Creeking when turning steering wheel

    If you want to look into it yourself further, buy a tool called a stethoscope (a manual one). It looks like that tool that a doctor uses to listen to your lungs/heart,, but it has a long sender metal probe to transfer noise to your ear. You can have someone duplicate the noise and you can use...

Latest posts

Forum statistics

Threads
107,087
Messages
1,181,310
Members
16,153
Latest member
lapochkarr

Members online

Total: 460 (members: 1, guests: 459)

Share this page

Back
Top