Recent content by Greg95SHO

  1. G

    95 ATX parts wanted

    Due to a minor front collsion, I need these parts. Car is white Hood Right headlight Right cornering light Headlight mounting panel Also need: windshield pillar moldings(grey interior) Front seats with good leather Thanks, Greg 619-212-6335 I'm in the San Diego area, can pay...
  2. G

    ccrm replaced--still no fuel pump

    No power to inertia switch before or after repalcement ccrm put in. Yes, it is the correct J code as the original. Thanks for your help. I'll keep looking for a bad ground. The car ran fine and had good power the day before it wouldn't start so I don't think it's a bad fuel pump problem? Greg
  3. G

    ccrm replaced--still no fuel pump

    The fuel pump ran momentarily with the FP pin grounded, not continuosly. I guess I missed something here? Greg
  4. G

    ccrm replaced--still no fuel pump

    Is the pump grounded by the fuel tank or where else do I check for ground?
  5. G

    ccrm replaced--still no fuel pump

    Car running fine and then wouldn't start next day. No fuel. I have no power to the fuel pump cut off switch in trunk and got a replacement CCRM with relay and still no power. Fuses in box by firewall are all fine. Grounded feed at firewall and pump ran for a few seconds. What else could be...
  6. G

    Control module with fuel pump relay needed

    For 95 ATX--"j" code... The box by the radiator on the drivers side Anyone have one cheap? Greg
  7. G

    New ford rings for 3.0---hone grit?

    Thanks for the responses! The rings are stock ones in Ford bags. The top ring has a silver edge which I'm not sure means. I can take them to a machinist to verify material. I know the hi-perf rings need a finer hone grit than iron rings. Greg
  8. G

    New ford rings for 3.0---hone grit?

    Yes, I just want to very lightly hone the cylinders so the rings seat well. The 3 arm stone style then is ok for this? I just dind't know if the stock rings were iron or moly. Thanks, Greg
  9. G

    New ford rings for 3.0---hone grit?

    There is no wear on the cylinder walls but I want to bottle hone the cylinders with the engine in the car. What grit hone do I get to use with the stock Ford rings? I was lucky enough to locate a set of the stock rings. Thanks in advance. Greg
  10. G

    1991 won't start after running hot

    The timing belt looked fine and had proper tension...I don't see how it could jump a tooth. Can the heads be repaired or are they junk? Greg
  11. G

    1991 won't start after running hot

    I'm helping a friend do work on a 91 plus model that he was driving on the freeway. The temp gauge went into the red zone and he pulled over right away. The coolant was bubbling after shut down. There was a coolant leak that he fixed the next day. He turnd the motor over with the spark plugs out...
  12. G

    Need valve shims ASAP!

    The 4 intakes had 2675 shims in them with .23 clearance. They do seem unusally thick but I'm not sure why. The car has 121K miles on it and I assume it had its 60K done. Does anyone know why Ford no longer offers the shims? Seems like they are abandoning these cars. Greg
  13. G

    Need valve shims ASAP!

    I was able to get what I need from a motorcyle dealer. Thanks. Greg
  14. G

    Need valve shims ASAP!

    I'm in the middle of doing an adjustment and don't have these sizes. Our local Ford dealer says they no longer can get the shims. I need fourr(4) 2700 and one(2) 2725 My cell number is 619-339-6937 if you got what I need. Thanks, Greg
  15. G

    sho mechanics in San Diego

    Mike, Send me an email and we can discuss this more. No problem if you want to see the work done. Greg
See more

Latest posts

Forum statistics

Threads
107,080
Messages
1,181,216
Members
16,144
Latest member
14blkbeauty

Staff online

Members online

Total: 756 (members: 5, guests: 751)

Share this page

Back
Top