Recent content by 1stGenSHO

  1. 1

    Noise from accessory belt area, what is it?

    Is it possible to replace only the bearing of the idler pully? It looks like it could be pressed out. (If it does not fall out on it's own..) 1stGenSHO
  2. 1

    Still Having MTX problems......

    I'm assuming it currently has ATX fluid in it? (I only ask because I've had mechanics offer to top off the MTX with 90 weight ****!) If the fluid is ok, it sounds like the trans may have been ran low on fluid. Does it get worse after it heats up? 1stGenSHO
  3. 1

    Back firing and hard starting....sometimes

    Sounds like the Camshaft ID sensor could be going bad. These symptoms are typical when the sensor is disconnected also. 1stGenSHO
  4. 1

    Testing the coil pack

    Ha Ha. I'll crank the engine, you check for spark!
  5. 1

    felpro oil pan seal

    Yes, the Felpro set comes with both seals. Don't know about the pickup tube gasket. 1stGenSHO
  6. 1

    Testing the coil pack

    Hello Everyone, Does anyone know if there is a procedure to test the coil pack using an ohm-meter? Chiltons seems to skip it for the SHO. Thanks, 1stGenSHO
  7. 1

    Smog Check Failed? NO too high... suggestions?

    GEN1SHO, I just failed my smog check in Arizona for the same exact thing in my '90 SHO. Although mine is bone stock, the cause is the cats. After 12 years of abuse they have given up. If you don't want to replace the whole Y-pipe you should be able to have new cats welded in for much less $...
  8. 1

    Converting A/C to R134

    ProjectSHO89, I'm prety sure it's munched. When the A/C quit it made a terrible grinding noise and the belt squeeled awhile before the clutch released (engine was slightly above 3k rpm). At startup I can get the clutch to engage once, but it sounds like the compressor is grinding rocks and the...
  9. 1

    Converting A/C to R134

    Thanks for your help guys, I really appreciate your advice. I think the car is beyond a conversion kit though, and because it is still charged with R12 I will take it to a shop. (A/C clutch engages but cannot rotate compressor at any rpm.) Because of the dead compressor, I'm assuming other...
  10. 1

    Converting A/C to R134

    Has anyone coverted their A/C system to R134 recently? I am trying to get a ballpark figure before contacting some shops. My compressor (R12) locked up while cruising on the freeway and I figure that changing to R134 at this point would not be much more. Thanks, 1stGenSHO
  11. 1

    My 90 runs too hot with the AC on?

    There is something wrong with your cooling system. I run around Phx,Az in my '90 and do not have problems. I'm still running R12 for the A/C, but I don't think that would make a difference. If the fan is running ok, it's probably the radiator or thermostat. Good luck. 1stGenSHO
  12. 1

    No Tachometer - Is it the CPS or CID?

    I have used the Autozone CPS and CID sensors with no problem on my '90. I have never heard of one of these sensors going without the car running like crap though. Check out that tach before you go through the trouble of replacing a sensor that is probably ok. 1stGenSHO
  13. 1

    Oil Pan Gaskets

    I just purchased that same set from carparts.com. It includes the two rubber end seals plus two tubes of the black RTV. 1stGenSHO
  14. 1

    STRUTS

    I'm also thinking of replacing the springs&struts on my '90. I know it needs struts, but not sure about the springs. The rear end is sagging a bit, but it is level and I like the look. Will new springs with a stock ride height raise the rear so the car does not sit parallel to the ground? If so...
  15. 1

    cruise not working

    More than likely something was not re-connected. The cable on mine was left undone at the throttle body. 1stGenSHO
See more

Latest posts

Forum statistics

Threads
107,093
Messages
1,181,338
Members
16,157
Latest member
poffffd

Members online

Total: 297 (members: 1, guests: 296)

Share this page

Back
Top