Search results
-
How to remove the Crank Pulley Bolt!?
Ok, so I think I'll try the "Starter Bump" method. But this brings up another question... I've had a couple of breaker bars and they both broke (I like to abuse them).... one was a husky and the other was a craftsman. Soooooo, any recommendations on who makes a good, tough breaker bar? Any...- bleavitt23
- Post #6
- Forum: Gen 1 & 2 - Engine, Exhaust, Drive Line & AC syste
-
How to remove the Crank Pulley Bolt!?
Alright. I'm trying to get to the CPS for replacement but the darn bolt for the crank pulley just won't come off. I've been working on it for 3 days now with a 500 ft/lb working torque impact gun but to no avail. This bolt isn't reverse threaded is it? I don't want to heat the bolt because I...- bleavitt23
- Thread
- Replies: 9
- Forum: Gen 1 & 2 - Engine, Exhaust, Drive Line & AC syste
-
93 MTX STILL Won't Start
I was trying to put off replacing the CKP for as long as possible, but with the codes I got I somehow knew in the back of my mind I would have to do it. I'm about halfway there now I just need to get the pulley remover to get the rest of the way. At least if it's not the problem I won't have...- bleavitt23
- Post #6
- Forum: Gen 1 & 2 - Engine, Exhaust, Drive Line & AC syste
-
93 MTX STILL Won't Start
Hey Guys, Ever since I got back from vacation last month the SHO has been crapified. At first it would start and run OK (except for the bucking and studdering upon acceleration), but for a month now it won't start at all. So far I have replaced the CCRM, CMP, Spark plugs and wires along...- bleavitt23
- Thread
- Replies: 9
- Forum: Gen 1 & 2 - Engine, Exhaust, Drive Line & AC syste
-
car won't start (again)
I did not change it due to the fact that it was working fine most of the time and I needed to save as much money as possible for my vacation. I did get a chance to pull the codes at work today and they are as follows... KOEO Codes- 116 - Coolant temp higher or lower than expected 114 -...- bleavitt23
- Post #6
- Forum: Gen 1 & 2 - Engine, Exhaust, Drive Line & AC syste
-
car won't start (again)
I keep forgetting to bring the code scanner to work but I'm doing that tomorrow. No Vacuum leaks to my knowledge. Haven't checked the grounds yet. I am just weirded out that this would happen after just sitting for a week and a half.- bleavitt23
- Post #4
- Forum: Gen 1 & 2 - Engine, Exhaust, Drive Line & AC syste
-
car won't start (again)
Hey guys, I'm really hoping for some verification here. A little while ago I was having problems with the CCRM not relaying power to the fuel pump (I know it was the CCRM because when the fuel pump would not prime or anything all I had to do was give the CCRM a good whack and it would start...- bleavitt23
- Thread
- Replies: 5
- Forum: Gen 1 & 2 - Engine, Exhaust, Drive Line & AC syste
-
How do I tell if the CCRM is bad? (Intermittent starting problem)
Hey guys, I have been having a problem with starting the SHO lately. It is a 93 MTX. 2-days ago I was about to go to work when it wouldn't start. This made 3 times this has happened in the last couple of weeks. The first time, it wouldn't start in the morning but when I got home from...- bleavitt23
- Thread
- Replies: 1
- Forum: Gen 1 & 2 - Engine, Exhaust, Drive Line & AC syste
