PBIR Test n Tune Late October

[32MTX]

man u must drive like an animal

I have yet to blow a diff pin and I'm not easy on em, is that number 2 in like a year or so? hahahaha

get the next one welded or a quaife and forget about it, I'm thinking of getting one of my spares welded for the next time I got the trans or engine out

 

[K-Dawg]

Knock on wood, I have yet to break one either, and I've done plenty of tire spinning.

 

[SuperchargedSHOguy]

man u must drive like an animal

I have yet to blow a diff pin and I'm not easy on em, is that number 2 in like a year or so? hahahaha

get the next one welded or a quaife and forget about it, I'm thinking of getting one of my spares welded for the next time I got the trans or engine out

Yeah, I think I will weld the spare transaxle I have sitting here for another SHO. I never busted a diff either, but I also don't drive it like I stole it.

 

[32MTX]

funny shit is, about 10 minutes after that post

I whent to start my car, turned over a little bit, then GRINDING noises

shit... either a flywheel or a starter.... took the starter out and only one tooth on my aluminum flywheel was rounded.... so I replaced the starter, it was binding up and cranking a lil slow...... got a new remmy on it.... lifetime warranty, no reman crap... looks beautiful and cranks over like a damn diesel gear reduction starter!

I was getting a lil worried about having to pull the flywheel, especially since it seemed like it only did it on one spot of the flywheel...... whew!

 

[SHOtime2511]

Never blown a diff here either.
I'm pretty easy on mine now days though.
The increase in weight from the wagon probably didn't help.

 

[chrism3784]

I don't really drive it hard at all. Very rarely spin out, if ever. Just bad luck. Next one will be welded before I put it in. Where would I go about getting that done. I may have to take to trans shop just to disassemble it to the diff and ship it off to someone that knows how.

 

[SHOtime2511]

You can buy the how video from Josh,but I would probably still take it to a shop.
There is so much crap inside of them.

 

[SuperchargedSHOguy]

You can buy the how video from Josh,but I would probably still take it to a shop.
There is so much crap inside of them.

One I took apart a few years ago had a spring or 2 fly out, lol.

 

[chrism3784]

LOL, I'll bring to a shop. I see someone on the classified welds them, sent them a pm.

 

[32MTX]

i think st louis sho welds them, I seen some pics hes posted, looks fn awesome

 

[SuperchargedSHOguy]

FYI I can weld them as well... you take apart and reassemble.

 

[SHOtime2511]

One I took apart a few years ago had a spring or 2 fly out, lol.

I took apart the old Civic transmission a blew up a year ago.
I'll never do that again.
Yep,I've blow up a Civic transmission but never a SHO trans.

 

[32MTX]

U can just about 1 hand a civic trans. I think a sho trans is rather large, ESP for it's age. I wonder what kind of stockpile big hp civic owners keep

 

[SHOtime2511]

They hold up pretty well from what I understand.
Civics never make shit for low end tq though,even boosted.

 

[32MTX]

so less then a week to go....... anyone still going?

 

[SHOtime2511]

Im still going.

 

[SuperchargedSHOguy]

Im still going.

Brian, can I ride with you? My SHO is not ready yet and my Jeep is down at the moment, lol.

 

[32MTX]

u get a new sho?

 

[SuperchargedSHOguy]

u get a new sho?

See signature

 

[SHOtime2511]

Sure,most likely in the Civic though.
Lots of shit going on,have not had a chance to get the tuning done yet.