Hesitation full throttle and low coolant but not leaking

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Krispykreme

New Member
Joined
Feb 17, 2020
Messages
12
Reaction score
1
Location
Fremont
I finally got the SHO up and running.

But other issues have developed.

1. Car hesitate under full throttle- it’s like it choking. Will do fine if I only press the accelerator half way (engine will rev freely to redline- full throttle- it’s just lurch).

2. Low coolant is showing up. And looks like there is a lot of air. I assume a full replacement of cooling system?

I don’t see coolant underneath the car, it’s not overheating, there is no coolant in the oil. But it just disappears. I am a lost on the cooling system.

94 Taurus sho
 

zoomlater

Supporting Member
Supporting Member
Joined
May 31, 2004
Messages
3,719
Reaction score
1,927
Location
Seattle, WA
So you got all the oil out of the plug wells and put in new spark plugs and wires (along with new spark plug well gaskets?)
 

zoomlater

Supporting Member
Supporting Member
Joined
May 31, 2004
Messages
3,719
Reaction score
1,927
Location
Seattle, WA
can you measure the fuel pressure at the Schrader valve
can you pull the engine codes now that its running
 

rubydist

SHO Master
Staff member
Super Moderators
Joined
Jun 25, 2007
Messages
7,530
Reaction score
3,411
Location
Denver
My experience with this engine and coolant going down but never seeing a drip on the driveway/garage floor is that it is leaking on the top of the engine and evaporating. I have had that from the crossover tube o-rings and also from the top radiator hose at the engine. The way I find it is to drive the car until the engine is warmed up and then open the hood and take the flashlight all over the top of the engine. There are numerous other places on the top of the engine where coolant can leak and evaporate so it never drips on the ground.

The full throttle issue could be anything from mis-timed cams to vacuum leaks to weak spark issues. The codes are the place to start for that one.
 

Krispykreme

New Member
Joined
Feb 17, 2020
Messages
12
Reaction score
1
Location
Fremont
Thank you guys

Codes

116
538
536
521

the leak is on the driver side on the lower block
 

rubydist

SHO Master
Staff member
Super Moderators
Joined
Jun 25, 2007
Messages
7,530
Reaction score
3,411
Location
Denver
116 = engine coolant temp sensor out of range
538 = no goose test performed during koer test
536 = brake on/off switch shorted to ground
521 = (not on my list)

please also do the koeo test, that will pull out the stored codes which are typically more useful to me.
 

tracy_s_1993_atx

SHO Member
Joined
May 31, 2003
Messages
183
Reaction score
48
Location
Plano, Texas
521 - Power Steering Pressure Switch (PSPS) - circuit switching not detected.

539 - A/C or Defroster on

10 - not sure as this should be a 3 digit code

189 - Heated Exhaust Gas Oxygen Sensor - voltage signal not switching ; indicates "lean" during part throttle. Bank #2

211 - Profile Ignition Pick-up (PIP) sensor - circuit failure

212 - Loss of ignition Diagnostic (IDM) signal - short to ground in Spark Output (SPOUT) circuit.

219 - Ignition system problem -Spark Output (SPOUT) signal open circuit (no spark advance timing).

528 - Clutch Switch(CS) - circuit failure

542 - Fuel Pump(FP) circuit open connection - Electronic Control Assembly (ECA) to motor ground.


Second reading

189 - Heated Exhaust Gas Oxygen Sensor - voltage signal not switching ; indicates "lean" during part throttle. Bank #2

211 - Profile Ignition Pick-up (PIP) sensor - circuit failure

212 - Loss of ignition Diagnostic (IDM) signal - short to ground in Spark Output (SPOUT) circuit.
539 - A/C or Defroster on

10 - not sure as this should be a 3 digit code

189 - Heated Exhaust Gas Oxygen Sensor - voltage signal not switching ; indicates "lean" during part throttle. Bank #2

211 - Profile Ignition Pick-up (PIP) sensor - circuit failure

212 - Loss of ignition Diagnostic (IDM) signal - short to ground in Spark Output (SPOUT) circuit.

219 - Ignition system problem -Spark Output (SPOUT) signal open circuit (no spark advance timing).

528 - Clutch Switch(CS) - circuit failure

542 - Fuel Pump(FP) circuit open connection - Electronic Control Assembly (ECA) to motor ground.


Second reading

189 - Heated Exhaust Gas Oxygen Sensor - voltage signal not switching ; indicates "lean" during part throttle. Bank #2

211 - Profile Ignition Pick-up (PIP) sensor - circuit failure

212 - Loss of ignition Diagnostic (IDM) signal - short to ground in Spark Output (SPOUT) circuit.
 

luigisho

SHO Member
Joined
Nov 2, 2001
Messages
13,323
Reaction score
5,189
Location
va beach,va
That's alot of electronic system codes. My first guess, without taking alot of time looking at all of it, is you have a PCM or wiring issue. SPOUT is no bueno.
 

BaySHO Performance

SHO Member
Joined
Feb 25, 2001
Messages
920
Reaction score
686
Location
SF South Bay
The 211 is worrisome, but usually the car dies completely because the water pump leaks onto the CPS, shorting it out.

Checking codes:

http://wiki.wikisho.com/wiki/EEC_Self_Test_Procedure

The '10' is the signal between displaying the On Demand codes (those that happen at the moment of the test) and stored codes from driving the car. Rather than a paper clip:

https://www.amazon.com/INNOVA-3145-...+ford+obd1&qid=1583520232&s=automotive&sr=1-2

The leak on the block sounds like one of the rubber ends to a heater hose has split. The hose is attached to the block at one end and heater pipe at the other. The rubber portion can be replaced with a short length of bulk hose.

These are useful for pressure testing the system:

https://www.amazon.com/Stant-12270-...ure+Tester&qid=1583522533&s=automotive&sr=1-1

They are a little pricey, so you may be better off borrowing a tester from Autozone. You pump the system to the blue 16lb. arrow. Be sure to protect the alternator from getting wet with a plastic bag.

The last time I had the same symptoms as you: runs fine under gentle acceleration, bogs down under load, it was because the filaments on the MAF were dirty. Can be spray cleaned with electric parts cleaner. May also be a loose air hose clamp at the throttle body, or a vacuum leak somewhere else.
 

luigisho

SHO Member
Joined
Nov 2, 2001
Messages
13,323
Reaction score
5,189
Location
va beach,va
If you can get it to start and run then I would suggest you clear the codes, run the car, and see which ones come back.
 

rubydist

SHO Master
Staff member
Super Moderators
Joined
Jun 25, 2007
Messages
7,530
Reaction score
3,411
Location
Denver
539

10

189

211

212

219

528

542


Second reading

189

211

212

That list of codes is impossible to be correct. Please post a video of the codes being flashed out so we can confirm what they really are.
 

luigisho

SHO Member
Joined
Nov 2, 2001
Messages
13,323
Reaction score
5,189
Location
va beach,va
I will take a video.

The codes were from innova OBDi reader.

how do I clear the codes?
Just unhook the battery, let it sit for about 20min and hook it back up. Then if it starts and runs and there are issues codes will trip again.
 

Forum statistics

Threads
107,294
Messages
1,183,253
Members
16,130
Latest member
raymo23

Members online

Back
Top